Kennedy .

Experience

• 

  Indonesia Power

  Mar 2017 - Apr 2017

  Internship ( Electrical Maintenance Division )

  Intership at Kamojang Geotermal Power Plant in Electrical Maintenance Division. Learning and analysis about Excitation and Capability Curve Generator Unit III. Intership In 1 month

• 

  PT XD Sakti Indonesia

  Dec 2019 - Feb 2021

  Junior Electrical Design Engineer

  1. Checking transformer design, make renewal, and repair the design with Solidworks and AutoCAD software, provide advice on the design, and manufacturing process according to IEC-60076 Standard.2. Make the bill of material and part list for 60MVA transformer, create work contact Sheet to inform other departments about special treatment and troubleshooting in the production process and transformer parts.3. Successfully renewal and repair 2D drawing, as well as Build the 3D design for 60MVA150/22kV AIS/GIS and 167MVA500/275kV ELIN Power Transformer.4. Give advice and assist to QC and Production department about the transformer production process according to IEC-60076 Standard. Show less

• 

  APRIL

  Feb 2021 - Sept 2022

  Electrical Project Engineer

  Assigned as an engineer in Power Distribution Systems, Turbine Generator(Steam), and Cooling Tower Projects.▪ Prepared and reviewed Target Project Cost, Bill of Quantity, and Material Take-Off.▪ Prepared and reviewed on Technical Evaluation Sheet for Tendering on Power Transformer, Distribution Transformer, and Cables.▪ Prepared and checked Single Line Diagrams, Motor List, Load List, Cable Sizing, Cable Tray Design, Transformer Sizing, Motor Control center List (MCC), Lighting Design, Grounding System, and Electrical Labor Quantity.▪ Reviewed and commented on 450MVA, 200MVA, and 70MVA Power Transformers, 150kV&33kV Gas Insulated Switchgear, 20kV and 6.6kV Air Insulated Switchgear, and TG-09 135MW and TG-10 330MW Turbine Generator design drawing, calculation sheet, Bill of Material list, and Engineering document issued by consultants and vendors.▪ Prepared Material Take-Off based on design engineering requirements and create Purchase Requisition to Procurement division.▪ Withness Equipment FAT and SAT as per Technical sign-off document.▪ Supervision Contractors and Vendor’s work according to technical requirements, procedures, and quality. Responsible for check out and commissioning of electrical equipment as per schedule and Procedure. Show less

• 

  PT PERTAMINA HULU ROKAN

  Sept 2022 - now

  Power System Engineer

  1. Assigned as an engineer in Power Generation and Transmission(PG&T) department at PT. Pertamina Hulu Rokan by PT. Permata Karya Jasa (PERKASA) is a third-party provider of partners.2. Do an assessment for transfer load or switching opportunity, review the switching procedure, and operating procedure to avoid unwanted trips or faults during switching or power system operation.3. Provide technical support and recommendations for operation and maintenance of power generation, 230kV, 115kV,&44kV Transmission, 13.8kV distribution system, Substation, protection, and auxiliary device.4. Collect outage event data, analyze the data, discuss with the related team, provided recommendations, and make the report. Generally, use EnerVista UR Relay for checking outage event data.5. Perform load flow analysis, short circuit analysis, and protection coordination in the Rokan area with ETAP Software.6. Conduct equipment diagnostic based on electrical tests. Witness product FAT and review testing results.7. Perform Pre-FEED Study and adequancy analysis for upgrading or develop existing power generation, transmission, distribution, and substation.8. Assists substation development project, PG&T Project, Major Capital Project, Well Development Project, 25MW Solar Powerplant, and Capacitor Bank 4x8MVAR. 9. Create Management of Change (MOC), Conduct Pre Safety Start-up Review before Start-Up. Show less