Joseph Pacifico

Experience

• 

  Komag Inc.

  Aug 1995 - Aug 2000

  Engineering Technician

  Monitor, set up test cell parameters, calibration, alignment, electrical and complex testing.• New Product Introduction Activities including Machine Installation, Product Qualification, Document generation, Setup and qualification of manufacturing lines.• Generate new Process Control Limits, Procedures and Manufacturing Process Flow for Production.• Implement and introduce new process changes in manufacturing including HF signal testing (I14H, R14H, I14N signal measurements) at the Quality Control Department.• Failure Analysis of Optical Storage Devices Field Returns from Customers including Block Error Rate and Parity Output Failure investigations.• Coordinate with vendors and suppliers on Machine Failure Investigations and Process Improvements.• Perform DOE's including Qualification of New Materials to reduce cost while maintaining /exceeding present quality.• Perform Engineering Projects/ Evaluations including Cycle up Evaluations, Machine Parameter Evaluations and Stress Reliability Test Measurements.• Yield Improvement through Pareto Generation / Top Failures Identification and Process Modifications• Automated electro-mechanical assembly process in clean room environment using robotic work cells, reducing head count requirement 65%, production space 40%, and scrap 20%.• Perform routine Preventive Maintenance Procedures on optical disc manufacturing lines.• Provide continuous line support to production through troubleshooting and process parameter Show less

• 

  Xilinx Inc.

  Aug 2000 - Nov 2007

  Planner Scheduler

  Expedite work in process for production incoming and outgoing materials.• Verify inspect the inventory and cycle count• Interface with production supervisors and managers for any changes in schedule to provide efficient supply parts to avoid unnecessary downtime.• Coordinate with production planners for any schedule priorities.• Prepare daily manufacturing schedule on test floor.• Coordinates with test supervisor for any priorities that need to expedite first.• Interface with engineers, manager planning for equipment needed to establish production layout.• Attend daily production meetings to discuss downtime and production output.• Set goals and target for the quarter.• Update specification for any particular device to avoid delay in production.• Discuss issues with maintenance to minimize downtime.• Prepare daily, weekly and monthly report.• Provide engineering support for any update and special request.• Interact with outside vendors for any specification issues by using exams application. Show less

• 

  Abbot Vascular Devices

  Jul 2014 - Mar 2015

  Mechanical Assembler Technician

  Perform inceptions for in process verification, pre test, pre seal and final inspection• Knowledgeable in manufacturing equipment and tools for measurements like caliper, micrometer, pin gauge and microscopy• Ensures compliance with quality standards in process and finished products with company standards• Perform EL HR line clearance before start and every lot change• Clean tools and equipment per documented procedures. • Record information on approved documents.• Follow standard operation procedure per NPI• Cross train other areas for flexibility of work• Dispose hazardous waste material on corresponding hazardous waste areas. • Resolve problems and make routine recommendations..• Train other employees when necessary.• Maintain all certifications required to remain in compliance with USDA Show less

• 

  Minaris Medical America formerly Hitachi Chemical Diagnostics

  Mar 2016 - Apr 2022

  Engineering Technician

  Set up, operate, production equipment, Optical Coverslips Inspection System, Usho Automated Tooling, Biodot and computers. Perform routine Preventive Maintenance Procedures on BioDot machine in manufacturing lines.• Provide continuous line support to production through troubleshooting and process parameter.• Assist R&D in the validation of experimental run equipment and tools in manufacturing• Maintain equipment parts and material inventory• Organize and maintain logs for manufacturing equipment• Respond in a timely manner to manufacturing needs• Ensure manufacturing documentation for production is organized, accurate, and complete according to GMP regulations on a daily basis• Advise supervisor of excessive number of damaged or defective parts and request replacement supply of standard parts in a timely manner• Clean and maintain work area• Turn off and lock-out equipment when not in use Show less

• 

  Lin Engineering - Motor Specialists in Motion

  Apr 2022 - Nov 2023

  Mechanical Engineering Technician

  -Support design reviews to ensure that parts can be manufactured efficiently and in compliance with customer requirements-Work with cross-functional teams to implement process improvements and execute cost/cycle-time reduction initiatives-Conceptualize and create fixtures to support manufacturing using 3D CAD software-Provide technical guidance (product and process) to all functional departments as required-Process engineering change orders and lead the implementation process-Support process improvement activities and cost reduction projects-Create prototypes for R&D projects-Plan production schedule to ensure maximum order fulfillment-Purchase tooling to increase efficiency -CNC operation Show less