Andy Abdul Azis

Experience

• 

  Politeknik Energi dan Mineral (PEM) Akamigas

  Jan 2022 - Dec 2023

  Responsibility in Absorber Column rate modules Responsibility in liquid-vapor equilibrium rate modules Responsibility in Freezing Point & Flash Point rate modules Responsibility in Partial Molar Volume rate modules

  • Equipment Design Process Laboratory Assistant

    Jan 2023 - Dec 2023

  • Thermodynamic Laboratory Assistant

    Jan 2023 - Dec 2023

  • Oil and Gas Product Testing Laboratory Assistant

    Jan 2022 - Dec 2022

  • Physics Chemistry Laboratory Assistant

    Jan 2022 - Dec 2022
• 

  PPSDM MIGAS

  Mar 2022 - Mar 2022

  Jr. Process Engineer

  1. Reviewed the entire process and participated in discussions with the employees to understand at least 90% of the utility process area2. Conduct routine inspections on production equipment to detect potential technical problems.3. Monitoring operational parameters to ensure the reliability and efficiency of the production process.4. Completed a project to evaluate the performance of heat exchanger 03 with an efficiency of 51.39%.

• 

  PT Polytama Propindo

  Dec 2022 - Feb 2023

  Jr. Process Engineer

  1. Observed the entire process and also participated in discussions with the employees to understand at least 85% process in Polypropilene Plant.2. Reviewed the process and identified equipment or areas that required improvement.3. Designed the improvement by calculating, evaluating, and optimizing equipment or process to increase the process productivity.4. Completed the analysis of the water carryover problem in the nitrogen dryer scrubber (T-502) gas flow through calculation and simulation using Aspen Hysys. Show less

• 

  PT Trans-Pacific Petrochemical Indotama

  Jan 2024 - Feb 2024

  Jr. Laboratory Analyst

  1. Understand fuel oil testing using ASTM and UOP methods.2. Perform various chemical and physical tests on petroleum samples with standard laboratory equipment such as CFR Engine.3. Work closely with the research team and senior analysts to develop more efficient and accurate analytical methods.4. Conducted research on the effect of blending bioethanol and gasoline 90, with a composition of 7% bioethanol and 93% gasoline, achieving a research octane number of 92.4.

• 

  PT Pertamina Lubricants

  Mar 2024 - Mar 2024

  Jr. Process Engineer

  1. Observed, reviewed the process area, and also participated in discussions with the employees to understand the entire process.2. Overview of non-hydro laboratories as Quality Inspector (QI). In this case, QI is tasked with checking the quality of non-hydro products from vendors, such as lithos, drums, and cardboard.3. Discussed the problem probability which often happens in the main process and has to be done.4. Calculated and analyzed the heat and mass balance of the main process, especially the boiler process.5. Completed a project analyzing the efficiency of boiler performance in the utility unit, efficiency result of 80.7%. Show less

• 

  Vopak

  Sept 2024 - now

  Operations Technician

  1. Set up and organize equipment/systems for product movement to and from vessels and between tanks and other operational activities including proper documentation. 2. Monitor all operating machinery and equipment so that they operate and are maintained according to company operating standards and are ready for use at any time. 3. Check for product waste in all aspects, notify relevant parties, and seek ways to prevent it. 4. Implement good housekeeping and safety in the workplace. 5. Perform preventive maintenance and assist Maintenance Technicians when needed in repair work. 6. Identify and report any equipment malfunctions. 7. Cooperate with surveyors or owner's representatives to take measurements, sampling and temperature readings in accordance with approved procedures. 8. Record all pumping start/stop times and delays for vessels at the dock. 9. Mentor and train Apprentice Technicians in terminal operations. 10. High awareness of safety, health, environment and quality. 11. Conduct safety talks in the field during SOR; take immediate corrective action if needed; make clear reports in QoL. 12. Report unsafe acts, unsafe conditions, near misses, incidents and accidents immediately to Team Leader and SHEQ Manager and make clear QoL reports with make clear QoL reports with detailed descriptions and pictures13. Approach coworkers, management, contractors, and third parties and give them feedback on their (safety) behavior. feedback on their (safety) behavior. 14. Initiate and follow up on improvements in the area of SHEQ. Show less