Joefrey Gella

Experience

• 

  Canadian Marconi Company Middle East (CMC ME)

  Mar 2009 - Jul 2013

  Avionics Technician - C130 Modernization Program, Avionics Glass Cockpit Modification

  - Removal of LRU’s (Line Replaceable Unit) as required by EO (Engineering Order).- Read and interpret engineering drawing, schematic diagram, technical manuals. Understanding symbols, flags and general notes.- Deletion of wiring required by Engineering order.- Wire harness layout and ring out according to Engineering Order drawing diagram.- Route and install various wire harness and cable assemblies as per engineering drawing- Terminate a wide variety of connectors, splice and solder wires using appropriate tools.- Securing wire harness and performs ring out continuity checks on a various aircraft system to ensure electrical compatibility and safety of components.- Knowledge in Ground Test Procedure base on using EO’s and using test equipment ( IFR- 4000 / IFR- 6000 / ADTS 405...etc)- Capable in troubleshooting base on avionics modernization program.- Performed power check.- Installation of unit and components and other equipment to be installed in the aircraft.- Capable in Updating EFIS / EFB / T2CAS / CVDR / ARCDU / FMS software using laptop. All have individual software and steps base in EO’s & manufacturers advice.- Accomplishes regular task of modifying Aircraft's EFIS Electronic Flight Instrument System, ESIDS Engine/Systems Instrument Display System, radio, electronic and electrical systems as required in the Modernization program upgrades in accordance with the procedures and standards set forth in the applicable manuals, manufacturer’s specifications and applicable airworthiness authority regulations. Show less

• 

  Alsalam Aircraft Company

  Sept 2013 - Feb 2017

  Avionics / Electrical Technician - F15 SR Saudi Retrofit ( Production and Manufacturing)

  - Read and interpret of engineering drawing installation and schematic diagram, Hook-Up Sheets, Automated Drawing Part List, Drawing Change Notice including Engineering Order, Variance and Revision Change and Boeing Process Specifications. Understanding symbols, general notes and flag notes.- Layout of wire harness, routing and installation of forward fuselage.- Decode wire Hook-Up Sheet in electrical ground connection and boot splice areas and other electrical connection such as relays, transformers and switches in forward fuselage.- Installation of circuit breaker panels and installation of dummy parts in forward fuselage (fwd and aft cockpit console and in 3, 6, 10 door.- Termination of wiring, splicing, RF cables and fabrication of electrical wiring.- Securing and Inspection all wire harness and perform Wire Integrity Test (WIT) Show less

• 

  ADVANCE MILITARY MAINTENANCE REPAIR AND OVERHAUL CENTER(AMMROC)

  Jul 2017 - May 2020

  PRINCIPAL TECHNICIAN (AVIONICS)

   Perform schedule/unscheduled inspection as required in accordance with Original Equipment Manufacturers (OEM) procedures.  Perform operational checkout of aircraft avionics systems during pre-flight and post-flight as necessary.  Tests avionics equipment under simulated or actual operating condition to determine performance and airworthiness using test equipment such as IFR 4000, IFR 6000, Dukane ULB, Multi-meter, Air Data Tester (ADTS 505), and Tachometer Generator Tester.  Adjust, repair or replace defective components based on analysis of test results, following blueprints, schematics, handbooks and other technical documents using hand tools.  Calibrate, install or repair equipment to prescribed specification.  Services and maintain aircraft avionic system components.  Maintaining, servicing and inspection avionics aircraft system and related aerospace equipment. Troubleshoots and maintain assigned aircraft system, components and related equipment. Perform Preventive maintenance, Removal and Installation of ISR Pod (Intelligence, Surveillance and Reconnaissance Pod) and MX-15Di  Perform operational check of ISR (Intelligence, Surveillance and Reconnaissance) MX-15Di system and perform Boresight Calibration of MX-15Di Prepare parts for turn-in back into the supply system. Initiates material deficiency reports as required.  Practice good housekeeping, tool control, FOD awareness/prevention and safety at all times.  Accomplish paper work, aircraft logbook, Non-routine Card (NRC), AADMIS and documents or form in the office after completion of job. Show less

• 

  GLOBAL AEROSPACE LOGISTICS (GAL)

  Jun 2020 - now

  AIRCRAFT TECHNICIAN III (AVIONICS)

   Perform schedule/unscheduled inspection as required in accordance with Original Equipment Manufacturers (OEM) procedures.  Perform operational checkout of aircraft avionics systems during pre-flight and post-flight as necessary.  Tests avionics equipment under simulated or actual operating condition to determine performance and airworthiness using test equipment such as IFR 4000, IFR 6000, Dukane ULB, Multi-meter, Air Data Tester (ADTS 505), and Tachometer Generator Tester.  Adjust, repair or replace defective components based on analysis of test results, following blueprints, schematics, handbooks and other technical documents using hand tools.  Calibrate, install or repair equipment to prescribed specification.  Services and maintain aircraft avionic system components.  Maintaining, servicing and inspection avionics aircraft system and related aerospace equipment.  Troubleshoots and maintain assigned aircraft system, components and related equipment. Perform Preventive maintenance, Removal and Installation of ISR Pod (Intelligence, Surveillance and Reconnaissance Pod) and MX-15Di  Perform operational check of ISR (Intelligence, Surveillance and Reconnaissance) MX-15Di system and perform Boresight Calibration of MX-15Di Prepare parts for turn-in back into the supply system. Initiates material deficiency reports as required.  Practice good housekeeping, tool control, FOD awareness/prevention and safety at all times.  Accomplish paper work, aircraft logbook, Non-routine Card (NRC), AADMIS and documents or form in the office after completion of job. Show less