Antonio Santos

Experience

• 

  Bonatti S.p.A.

  Jan 1994 - Feb 1995

  PIPING Foreman

  • In-charge in supervising the erection of pipes.• Preparing daily time-sheet. Work schedule and to ensure that all materials and tools are well prepared.• Estimate piping material and worker requirements to complete the job.• Confer with managerial and technical personnel, other departments and contractors in order to resolve problems and to coordinate activities.

• 

  DJ Roque Construction Inc.

  May 1995 - Jul 1996

  Piping Supervisor

  • Responsible for all piping revisions and rectification works for all existing and new process line. In charge of quantifications as per code of specifications required by client. Monitors work progress and scheduling of all piping works including the installation of piping supports. Prepares the test packages, inspection activities, orientation / checking of piping, visual inspection, inspection of welding works, checking of materials based on specifications as per clients requirement. Supervises piping installation based on daily forecasted schedule versus actual to insure maintenance of the target working time.• Preparation of PTW and coordination to Shift Supervisor operation department.• Knowledge to read and interpret P&ID and Isometric drawings.• Conduct walkthrough with client field operator for the system lines for commissioning activities. • Conduct air blowing of sour gas line(jacketed lines) including distribution and condensate manifolds.• Conduct Steam blowing for main header line including branches such as utility lines for HP,MP and LP.• Conduct air freeing with the Nitrogen purging in instrument line,fuel gas line and line stripper.• Conduct rupture blowing with knife valve or plastic sheets.• Conduct final inspection with the client field operator in RFI( Request for Inspection).• Conduct final punch list and reinstatements. Show less

• 

  Alltech Contruction Inc.

  Jan 1997 - Feb 1998

  Piping Supervisor

  • Assigned to handle worker to perform various piping activities such as: -Fabrication and installation of different size of product pipe line. Cools water piping from intake pump to condenser installation of high pressure main steam piping primary super heater to steam turbine and installation of low pressure main steam piping from steam turbine to condenser.• Fabrication of inlet and outlet lines for water filter in Degasifier and Anion vessel in Demineralized water treatment plant. Show less

• 

  National Power Corporation Philippines

  Apr 1998 - Jan 1999

  Mechanical Commissioning Supervisor

  Conduct Pre commissioning & commissioning start-up such as air blowing, Steam blowing,instrument & plant air system,potable water system,fire water line system including fire monitors/fire hydrants & boiler feed water system.Conduct motor solo run & functional testing.Conduct reinstatement & final punch list.

• 

  National Power Corporation

  Apr 1998 - Jan 1999

  Mechanical Commissioning Supervisor

  • Conducted and performs pre-commissioning / commissioning, start up and operation of Instrument /Plant Air System, Potable Water System, Fire Water System, Demineralization Unit, Steam Boiler, BFW System.• -Conduct routine checking, inspection, observe running condition of all machinery equipment, operates utility unit safely while providing the required utility to process units,

• 

  DJ.Ray Mcdermott

  Aug 2000 - Nov 2001

  Mechanical Commissioning Supervisor

  Instrument/ Service Air SystemEmergency Diesel Generator SystemFire Water SystemBoiler UnitBFW SystemDemineralization UnitDesalination UnitStabilization UnitFeed / Tank age System• Reports to the Lead Commissioning Engineer of the Commissioning Department.• Perform pre-commissioning activities as per commissioning Engineer’s.• Instructions that includes air blowing, water flushing and performs functional testing as per Commissioning procedures.• Conducted Motor Solo Run Test taking vibration, bearing temperature and RPM• -Assisted vendor representative for chemical cleaning, Lube oil flushing, Turbine Compressor and Generator functional testing.• Perform vessel internal cleaning until final closure.• -Conducted in leak testing and rectify leakage found during testi Show less

• 

  JRay McDermott

  Aug 2000 - Nov 2001

  Mechanical Commissioning Supervisor

  BFW SystemDeminiralization unitDesalination unitPerform air blowing as per P&ID Drawings.Conduct motor solo run & functional testing.Conduct HP LP MP Steam blowing including steam traps & condensate & distribution manifolds.Conduct reinstatement & final punch list.

• 

  Clough Niugini Ltd.

  Oct 2003 - Feb 2005

  Mechanical Commissioning Supervisor

  Instrument / Service Air SystemEmergency Diesel Generator SystemFire Water SystemBoiler UnitBFW SystemDemineralization UnitDesalination UnitStabilization UnitFeed / Product Tankage System• Responsible for the pre-commissioning, commissioning, start up and operation of the above facilities.• Coordinate final punch and punch clearing.• Obtain PTW for the Pre-Commissioning activities• Conduct air blowing preparation and reinstatement-N2, C3, MR Turbine Compressor Lube Oil Flushing-Motor Solo Run-Instrument / Plant air system-MP, LP, HP steam system-Fuel gas system• Commissioning of steam tracing system, distribution and condensate manifolds.• Responsible for the PTW for the Pre- mechanical commissioning activities.• Perform preparation of air blowing and reinstatement as per method of statement.• Perform air blowing by using rapture disk as per method of statement.• Request to the lead commissioning engineer for the inspection of the circuit with the client representative field operator.• Responsible for the MP, LP, HP steam blowing activities and conduct inspection with the client representative field operator.• Commissioning of all steam traps, distribution and condensate manifolds.• Assisted to vendor representative for HP steam blowing for all steam turbine lines.• Perform conformity check line and tightness test.• Assisted to vendor representative for chemical cleaning, lube oil flushing, turbine compressor and generator functional testing.• Conducted in leak testing and rectify leakage found during testing.• Commissioning of fire hydrants and deluge system• Coordinate final punch and punch clearing Show less

• 

  Clough Niugini Ltd.

  Oct 2003 - Feb 2005

  Mechanical Commissioning Supervisor

  Obtain Permit to work & conduct safety tool box meeting.Assigned in Pre commissioning & commissioning start-up such as plant air,instrument air,HP LP MP Steam blowing including condensate & distribution manifold & steam traps.Conduct motor solo run & functional testing.Conduct reinstatement & final punch list.

• 

  ABB Operation & Maintenance

  Oct 2005 - Jan 2008

  Power plant field operator

  Gas turbine generator systemAuxiliary oil pump and power oil pump systemHRSG/ Heat Recovery Steam GeneratorSteam turbine generator system

• 

  Chiyoda Technip Joint Venture

  Feb 2008 - Nov 2009

  Pre-Mechanical commissioning & Commissioning Supervisor

  • Obtain PTW for the Pre-Commissioning activities• Conduct air blowing preparation and reinstatement-N2, C3, MR Turbine Compressor Lube Oil Flushing-Motor Solo Run-Instrument / Plant air system-MP, LP, HP steam system• Assigned in lube oil flashing such as preparation for bypass line in turbine bearings and compressor bearings. Air blowing of lube oil return and supply lines, Preparation of wire mess for return and supply line from the lube oil tank, Monitoring of lube oil pumps such as power oil, emergency and two back-up lube oil pumps and coordination to control panel.• Commissioning of steam tracing system, distribution and condensate manifolds.• Responsible for the PTW for the Pre- mechanical commissioning activities.• Perform preparation of air blowing and reinstatement as per method of statement.• -Perform air blowing by using rapture disk as per method of statement.• -Request to the lead commissioning engineer for the inspection of the circuit with the client representative field operator.• Responsible for the MP, LP, HP steam blowing activities and conduct inspection with the client representative field operator.• Commissioning of all steam traps, distribution and condensate manifolds.• Assisted to vendor representative for HP steam blowing for all steam turbine lines.• Perform conformity check line and tightness test.• Assisted to vendor representative for chemical cleaning, lube oil flushing, turbine compressor and Jacking oil functional testing.• Conducted in leak testing and rectify leakage found during testing.• Commissioning of fire hydrants and deluge system.• Coordinate final punch and punch clearing. Show less

• 

  DJ Roque Construction Inc.

  Jan 2010 - Aug 2010

  Mechanical Supervisor

  • Obtain PTW for the Mechanical jobs.• Coordinate to the Operation Shift Supervisor and to the field operator if the auxiliaries are already isolated for the safety precautions.• Assigned in the Utility area such as Installation and alignment of a new reconditioned pumps and compressors. • Assigned for the removal and installation of tubing in Heat Exchanger,• Replacement of Internal parts for plate exchangers such as rubber gaskets and assembling.• Assigned for the removal in the Steam Turbines damaged blades and replacing into new one.• Assigned for the HP Steam blowing lines that connected to the Steam Turbine.• Assigned for steam turbine solo run.• Performed corrective maintenance for steam traps, condensate and distribution manifolds. Show less

• 

  JGC/KBR Joint Venture

  Dec 2010 - Dec 2011

  Mechanical Commissioning Supervisor

  -Obtain permit to work for the commissioning activities.-Conduct safety talk and tool box meeting for commissioning activities.-Assigned in night shift duty for commissioning activities in process area such as:-Steam blowing of sour gas line and rectification of distribution manifolds such as clogged steam traps and clogged heat tracing lines.-Conduct lube oil flashing for Turbines and Compressors including installation ofbypass lines for bearings of turbines and compressors. Fabricating of No.100 and200 wire mesh for inlet and outlet lines in lube oil tank.-Nitrogen purging for reactors (shell side and tube side), light and stripper lines and condenser lines.-Commissioning of pin fan cooling motors such as vibration, temperature and sounds abnormality.-Conduct air blowing preparation and installation of knife valve for rapture blowing as per mark up PEFS and procedures.-Conduct safety walk through with the client field operators.-Conduct air blowing, rapture disk, tightness test, nitrogen purging, air freeing, leak test, operational testing and functional test.-Conduct final inspection with the client field operators for acceptance.-Conduct final reinstatements. Show less

• 

  Daelim Philippines

  Jun 2012 - Aug 2013

  Mechanical Supervisor

  -Assigned in pipe rack structural at 8100 common, interconnecting 8300 p/r 1 & 2-Supervision of installation of rotating equipment such as centrifugal pumps andpositive displacement pumps including motor solo run until commissioning with thesuction and discharge lines.-Supervision of erection and double ending activities of pipes in the pipe rack including fitting fit-up.-Supervision in fabrication shop such as fit-up of all joints of pipes and fittings. Including underground piping.-Supervision of erection for flare structures. Show less

• 

  Petron Corporation

  Dec 2013 - Feb 2014

  QA/QC Mechanical Inspector for Hydrostatic Testing (special Project Group)

  -Assigned in hydrostatic testing and pipes inspection including leak testing.-Conduct walkthrough for hydrostatic testing including safeness.- Assigned in commissioning and pre-commissioning inspection such as steam blowing for HP,MP and LP steam, including rapture blowing and Air blowing.-Popping test of pressure safety valves.-Mechanical solo run inspection.-System test.-Leak test inspection.(pneumatic and Nitrogen).

• 

  Saudi Aramco

  Mar 2014 - May 2014

  Field Metal Mechanic I- Grade code 9

  -Assigned in South refinery-Coordinate to the mechanical Supervisor for the work order task.--Obtain PTW for the Mechanical maintenance jobs.-Coordinate to the Operation Shift Supervisor and to the field operator if the auxiliaries are already isolated for the safety precautions.-Installation and alignment of a new reconditioned pumps and compressors.-Removal of nonfunctional valves, gaskets and replace into new one.-Assigned for the removal and installation of tubing in Heat Exchanger,-Replacement of Internal parts for plate exchangers such as rubber gaskets and assembling.-Assigned for the removal in the Steam Turbines damaged blades and replacing into new one.-Assigned for the HP Steam blowing lines that connected to the Steam Turbine.-Assigned for steam turbine solo run.-Performed corrective and preventive maintenance for steam traps, condensate and distribution manifolds, pumps and motors. Show less

• 

  Petron Corporation

  Jun 2014 - Jul 2014

  QA/AC Mechanical Inspector for Hydrostatic Testing

  -Assigned in hydrostatic testing for pipes inspection including leak testing.-Conduct walkthrough for hydrostatic testing including safeness.- Assigned in commissioning and pre-commissioning inspection such as steam blowing for HP,MP and LP steam, including rapture blowing and Air blowing.-Popping test of pressure safety valves.-Mechanical solo run inspection.-System test.-Leak test inspection.(pneumatic and Nitrogen).

• 

  Technip

  Apr 2016 - Mar 2017

  Pre-Mechanical Commissioning & Commissioning Module Supervisor

  . -Conduct line checking of system before air blowing..-conduct drying and innerting..-Conduct Gross Air Leak Test (GALT).-Conduct Maximum Operating Process (MOP).-Conduct inspection and commissioning of Fire Monitor..-Conduct final Reinstatement and final punch list..-Hand Cleaning inspection of Hook-ups pipes before injecting of Chemical preservation.

• 

  Petron Bataan Refinery

  May 2019 - Jul 2019

  Petron Reliability Group Engineer

  Initial inspection of Drums such as UTG of wall, PT of welds sections including Dimesters prior for cleaning until for final inspection for acceptance until commissioning and functional testing.Initial inspection of Heat Exchangers and Fan coolers prior for cleaning of shell,tube bundles,heads,inlet and outlet nozzles.cheking of crack in guide railways,conduct UTG ang PT in shell until final inpection and hydro testing.Leak testing of valves such as motorized operated valve, gate, ball, check and butterfly valves. Show less