Experience

• 

  Atlantic, gulf & pacific company (ag&p)

  Dec 1990 - Sept 1991

  Mechanical engineer

  Supervising a multi-national team of Pipe fitters and Welders engaged on the construction UOT Project. Fabrication of high pressure Oil/Gas Pipelines and Piping from small bore to large bore Diameter to A.P.I. and A.S.M.E codes. Responsible for ensuring all mechanical and piping installations are in compliance with the specifications and that all documentation is completed. Responsible for inspecting shop fabricated and field erected piping and ensuring that contractor has effective quality control systems. Ensure piping installations are properly performed as per drawing and specification. Verify piping connections to equipment nozzles are not stressed and properly aligned. Clear hydrotest packages for test including pre-test walkdown. Supervise walkdown and punch of systems. Participate in area welding audits, ensure any area controlled inspection and test equipment is calibrated. Conduct equipment installation inspection per the ITP’s. Monitor equipment preservation activities. Inspect equipment foundation and verify survey results. Monitor installation of equipment, setting, cold alignment, hot alignment, clearances, correct support configuration, internal installation, packing trays, final closures, trim out insulation to ensure installation is in compliance with project specifications, witness flange bolt-ups, including verification on flange face condition and gaskets, inspect equipment after completion to ensure all components are per the drawing and report deficiencies on the pre hydro test punch list , ensure all welds are reported NDE is cleared in news before authorizing a pressure test packages for test, witness pressure tests including verification of temperature, pressure, and calibration of test instrumentation, safety device and certify leak tightness, assist in system turnover. Show less

• 

  Chiyoda corporation

  Oct 1991 - Jul 1992

  Piping mechanical engineer

  Supervising a multi-national team of Pipe fitters and Welders engaged on the construction ADMA-OPCO TRAIN 3 Expansion project. Responsible for ensuring all mechanical and piping installations are in compliance with the specifications and that all documentation is completed. Responsible for inspecting shop fabricated and field erected piping and ensuring that contractor has effective quality control systems. Monitor equipment preservation activities, inspect equipment foundation and verify survey results, monitor installation of equipment, setting, cold alignment, hot alignment, clearances, correct support configuration, internal installation, packing trays, final closures, trim out insulation to ensure installation is in compliance with project specifications, witness flange bolt-ups, including verification on flange face condition and gaskets, inspect equipment after completion to ensure all components are per the drawing and report deficiencies on the pre hydro test punch list , ensure all welds are reported NDE is cleared in news before authorizing a pressure test packages for test, witness pressure tests including verification of temperature, pressure, and calibration of test instrumentation, safety device and certify leak tightness, assist in system turnover, conduct reinstatement walkdown and log outstanding item on the punch list, monitor insulation installation including correct type and application, monitor heat tracing installation in coordination with the E&I inspector. Work with the operation team to carry out maintenance and reliability studies, root cause analysis investigation and management and to initiates actions for replacement or upgradation of equipment for improvement in work methods. Show less

• 

  Fluor daniel incorporated

  Apr 1993 - Feb 1995

  Mechanical engineer

  Supervises field construction by issuing work orders, resolving issues related to field piping design discrepancies and modification. Overall and day to day supervision of piping, prefabrication, erection and testing. Ensure mechanical completion of piping systems as per defined targets and development of action plans to achieve timely completion. Full implementation of all quality requirements. Timely and regular reporting of progress and quality towards construction superintendent. Supervise and instruct subcontractors with regard to quality, progress, field modifications. Arrange all means and efforts to achieve a maximum extent of work possibilities for subcontractors. Manage, coach Assistant Piping supervisors and painting and insulation supervisors. Control and check work of subcontractors in terms of quality control and quality assurance. Control subcontractor’s progress. Show less

• 

  Atlantic, gulf & pacific company, inc.

  Mar 1995 - Apr 1996

  Piping / mechanical supervisor

  Monitoring of Piping Installation from Fabrication shop to Platform off-shore interface. Prepare detailed Piping drawings for different upgrading projects on Natural gas & petroleum offshore fields Floating Production Storage Offloading (FPSO). Supervise offshore construction, hook-up and interconnection of piping and mechanical components. Preparation of shop drawings and hook-up spooling. Implementation of drawing revision, field change notices and as-built documentations. Performs or provides input for personnel evaluations on subordinate personnel. Involved in Hot Tapping works for offshore pipelines. Technical knowledge of construction quality control relating to single or multidiscipline construction quality control activities. Perform engineering and construction activities, which relates to an assigned area of responsibility. To prepare and help implement construction work packages for the erection and construction of offshore and onshore oil and gas facilities and projects respectively up to including mechanical completion, based on design. Develop construction work packages for the installation of the following types of equipment: Floor pedestal supports, Precision equipment, Wall mounted equipment supports, Large mechanical equipment platforms, Various sizes process vessels, Vertical axial flow pumps, Various sizes process vessels, and Rigid process piping jumpers. Work with the operation team to carry out maintenance and reliability studies, root cause analysis investigation and management and to initiates actions for replacement or upgradation of equipment for improvement in work methods. Show less

• 

  Sanko engineering

  Oct 1996 - Dec 1997

  Senior line checker / q.c inspector

  Ensuring fully detailed documentation of all welding activities are raised and completed prior to handover. Coordinating with Engineering and Construction and liaise with the Client on detail welding requirements. Ensuring that all Welding, Heat Treatment, any hardness testing, Inspection and Non-destructive testing are in compliance with the relevant codes and specifications. Ensuring the use of the correct welding procedures and verifying all Welder qualifications and monitoring both application and performance. Ensuring that all welding and testing related records form a complete package and reflect the ‘As Built’ integrity of the plant. Ensuring that all welding work is performed under controlled conditions and consumables used are in accordance with the specification. Ensuring that all installed pipe/fittings are to the correct specification and that the material is in accordance with the specified Material Traceability requirements. Line checking of various piping system ensuring line completeness with regards to latest piping configuration and conforming to the P&ID/PEFS. Development of work packages for hydro testing, pneumatic testing and service testing. Review “as built” and test documentation. Witnessing hydro test, flushing and air testing operations. Involve and reinstatement of piping components checking and clearing off punch list. Raised (RFI) request for inspection to clients for every completed piping system prior for testing. Check and update latest drawing revisions for piping arrangement and isometric as per P&ID/PEFS. Preparation and review of project specifications for materials, protection, concrete coating, thermal insulation, cathodic protection, fabrication, welding, hydro test and installation for rigid or flexible flowlines and trunklines, diverless connection and installation systems, subsea intervention works. Show less

• 

  Kellogg brown & root/ japan gas corporation joint venture

  Dec 1997 - Jan 1999

  Piping /mechanical supervisor

  Supervises field construction by issuing work orders, resolving issues related to field piping design discrepancies and modification. Plans, schedules & supervises the piping and activities from fabrication shop to site. Performs supervisory functions at the level established by Management. Ensures that quality procedure and standard is being implemented. Maintains and updates procedures for all technical and practical aspects of Mechanical and Piping Fabrication. Carries out technical reviews at LNG plant modification work ensuring that such modifications are implement. Responsible for the site piping fabrication, mechanical and piping/support installation, system testing and completion, and system turnover to Start-Up group. Provide. Resolve design deficiencies and prepare field change notices. Conduct line checking and punchlisting. Conduct system testing (hydrotest, pneumatic test and/or in-service leak test) and restoration. Conduct quality inspection, system completion and acceptance with the Engineer and Owner. Prepare Notice of Back charges to vendors/suppliers, subcontractors and/or consortium partners. Provides the necessary support to consultants and site construction contractors to ensure that their work schedule targets are achieved. Monitor of piping installation on underground facilities like, glass reinforced epoxy piping (GRE/GRP), high density poly ethylene piping (HDPE), carbon steel cement and epoxy lined piping and ductile iron piping. Attend weekly progress meetings with subcontractors. Issue written instructions (construction inspection reports) to subcontractors. Check the planning and physical progress of subcontractors. Supervise “punch out” of installed work. Supervise execution of all tests and inspections for the completion of Mechanical Completion and Hand Over documentation packages. Liaise with Safety Supervisor to achieve the application of Safe work methods. Show less

• 

  Bechtel corporation

  Apr 2000 - Aug 2001

  To develop, manage and maintain required Piping & Mechanical Design and Engineering procedures in line with best industry practices based on approved applicable standards. Participate effectively in the development of scope of work of Borouge Petrochemicals Project activities ensuring that latest approved technologies are applied and in compliance with applicable international standards. Performs construction quality control activities in a technical or administrative capacity within the piping and mechanical discipline. Responsible for the performance of on-site tasks related to quality control compliance. Plans, directs, supervises and manages site construction activities until pre-commissioning and commissioning stage. Supervision of piping, pre-fabrication, installation and testing. Ensures mechanical completions of piping systems as per defined targets and development of action plans to achieve timely completion. Fully implementations of all quality requirements. Timely and regular reporting of progress and quality towards construction management. Supervise and instruct subcontractors with regard to quality, progress, and field modifications. Control of field extras, non-conformities and work orders. Arrange all means and efforts to achieve a maximum extent of work possibilities for subcontractors. Manage; coach Assist piping supervisors and painting- and insulation- supervisors. Control and check work of subcontractors in terms of quality and quantity. Control subcontractor’s progress. Attend weekly progress meetings with subcontractors. Issue written instructions (construction inspection reports) to subcontractors. Arrange inspections and tests with client representatives and authority inspectors. Supervise “punch out” of installed work. Supervise execution of all tests and inspections for the completion of Mechanical Completion and Hand Over documentation packages. Show less Responsible for hydrostatic testing and flushing, procedure development, and testing; Prepared mechanical/ instrumentation modification and restoration instructions to facilitate testing; Coordinated system completions, transfers, and turnovers; Interfaced with Construction, Start Up, and Operations for resolution of restraints to expedite testing; Performed initial equipment energizations for operation of subsystems and components during original plant start up. Duties included finalization of Hydro procedures, coordination of testing with Maintenance and Operations, Hydro procedure test changes and preparation of Outage Hydro test reports. Responsible for implementation of ASME Code Section XI In Service Testing. Engaged in the inspection of piping fabrication pressure vessels, verticals and horizontal tanks including associated pipe work and heavy structural steel for the OGD Phase 2. Overseeing the installation of Pressure Vessels and site built storage tanks including the inspection of structural steel supports and piping components. Coordinating NDT activities, i.e. Radiography and MPI - Dye Penetrant Examinations. Other duties included visits to sub-contractors premises for inspection and reviewing documentation of completed fabrication prior to clients review and acceptance. Codes and standards used ASME VIII, API 650, ANSI, AWS Dl.l, Welding processes used S.M.A.W., G.M.A.W. and G.T.A.W. Review and interpret piping fabrication drawings, isometric drawings and check and inspect the actual installation. Conduct initial and final punch listing based on the latest drawings, bill of materials and specifications. Prepare construction punchlist and coordinate in the field prior to line completion. Inspect proper piping and supports installations, check piping components against its specifications and prepare piping inspection checklist prior to mechanical completion walkdown with the client. Show less

  • Senior Construction Engineer – Piping & Mechanical

    Feb 2001 - Aug 2001

  • Hydro Test Engineer / Piping Inspector

    Apr 2000 - Feb 2001
• 

  Mw kellogg

  Dec 2001 - May 2003

  Commissioning craft supervisor

  Line–up various line system ready for pre- commissioning works ensuring completeness of system, check proper blinding and access of system. Line checking of various piping system ensuring line completeness with regards to latest piping configuration and conforming to the P&ID/PEFS. Carried out water flushing, air blowing, pigging operation and chemical cleaning ensuring the cleanliness and good condition of piping system. Direct supervision of leak testing hydrostatic, pneumatic, and service test operation ensuring the whole system is free of leaks prior to hand over and start-up operation. Involved in punch listing and restoration of piping components and equipments ready for operation. Assist and work with the plant operators for gas-in operation. Participate in the development of the non-routine live gas operation procedures and provide support during emergency response situations when required. To review and carried out any design work by third parties and vendors and participate in some instances HZAP, HAZID, HAZOP, SAFETY and facilities audit. Participate on Realibility activities and investigation and indentify root cause analisys and management. Work with the operation team to carry out maintenance and reliability studies, root cause analysis investigation and management and to initiates actions for replacement or upgradation of equipment for improvement in work methods. Show less

• 

  Bechtel power corporation

  Jun 2003 - Nov 2003

  Senior piping engineer / designer

  Responsible for the organization and direction of construction engineering forces, piping and mechanical activities related to construction engineering, subcontracts and engineering liaison. Interprets design drawings and specifications. Carried out material take-offs to support engineering and construction work activities. Monitor of piping fabrications and installations in accordance with the project standards, procedures and specifications. Review and check specifications, procedures, method of statements, purchase orders, subcontracts, inspection reports, delivery schedules, and instruction manuals to assist on site activities. Initiate requisition for field materials. Direct coordination to construction superintendent to schedule construction field engineering work packaging, procurement of field materials and installation of equipments. Job knowledge in “Zero Accident” safety program. Provide the necessary technical assistance to the project construction team at requirement (e.g. subcontract evaluation, definition of the scope of work, construction schematics etc. Show less

• 

  Bechtel corporation

  Aug 2004 - Aug 2006

  Field piping engineer

  Provide Piping Design and Technical analysis and resolution of engineering problems. Provide direction and coordination of the construction team to execute the project successfully. Responsible for overseeing the piping and mechanical activities at fabrication and site engage in Onshore Processing Facility projects and providing technical assistance for constructability review with commitment to Safety. Generate and develop above ground and underground piping work packages. Monitor progress and preparation of deliverables of erection contract. Ensuring procedures and schedules are adhered to. Resolving and responding to technical queries from sub contractors. Review technical and engineering issues ensuring project quality procedures, standard, design and specification. Prepare and develop method of statement for the 7 kilometers HDPE underground well pipe line From OPF ISBL to 3 well pumping stations. Prepare method of statement for hydro testing of site erected tanks. Works on Technical Queries for field modification, field routes, as-built and discrepancies. Show less

• 

  Nigeria lng limited

  Sept 2006 - Dec 2006

  Senior mechanical inspector

  Work as NLNG Client Representative that responsible for overseeing the piping, mechanical and welding activities at fabrication and site engage in the construction of Train 6 NLNG NPP Project and providing technical assistance for constructability review with commitment to Safety and Quality. Monitor installation of rotating and static equipment, setting, cold alignment, hot alignment, clearances, correct support configuration, internal installation, packing trays, final closures, trim out insulation to ensure installation is in compliance with project specifications, witness flange bolt-ups, including verification on flange face condition and gaskets, inspect equipment after completion to ensure all components are per the drawing and report deficiencies on the pre hydro test punch list, ensure all welds are reported NDE is cleared in news before authorizing a pressure test packages for test, witness pressure tests including verification of temperature, pressure, and calibration of test instrumentation, safety device and certify leak tightness, assist in system turnover. Conduct reinstatement walkdown and log outstanding item on the punch list. Show less

• 

  Parsons fluor daniel llc

  Jan 2007 - May 2007

  Senior piping engineer

  Prepares hydro-test packages & test flow based on PFD furnished hydro-test diagrams and coordinate all activities involved in the test packages and punch list. Review the P & ID in conjunction with the piping specification to verify pressure test package limits, line checking to confirm isometric requirements and initiates action from construction section of deficiency punch list. Prepares sketches/ revises construction drawing to reflects “ AS BUILT “ condition for preparation of line checking/punch listing through isometric drawing or P&ID. Reviews/approves test packages for completeness of content and for latest revision of documents used. Supervise sub-contractor for hydro and pneumatic testing of pipe lines to ensure it meets the required pressure. Verifies contractors red marks on isometric drawings and P&ID test diagrams. Maintain Master Pressure Test P&ID for the purpose of monitoring and verifying system test completeness of hydro test packages. Uses Pro-Arc Web for clients/vendors document verification. Walk down piping system test packages for pre hydro punch list. Prepare all necessary documents prior to hydro testing. Keep all relevant documents and records of completed works Walk down piping system packages for post-test / reinstatement inspection. Inspect on going and completed construction piping activities. Prepare line check reports and record as required. Show less

• 

  Qatargas

  Jan 2007 - Jan 2012

  Mechanical engineer

  Main responsibilities: Responsible to undertake supervision, inspection and field engineering activities on behalf of Company in the area of mechanical works and ensure that these works are implemented in accordance with the Project Integrated Basis of Design and all Project requirements, procedures, budgets and schedules. To support Lead Mechanical Engineer in ensuring that Project HSE targets are met or exceeded. To ensure that the specified quality requirements for mechanical works are met. To ensure that mechanical works are executed in an efficient and timely manner in order to meet the Project time schedule and budget requirements. To enable, monitor and control the EPC Contractor in the execution of his responsibilities under the EPC Contract. To co-ordinate and provide expertise to ensure that the plant is built and will function in accordance with the Project requirements. To ensure that interfaces with other parts of the Project and all Project stakeholders are adequately managed. Primary accountabilities on: mechanical static and rotating equipment (including receipt inspection), internals installation, witness and verify testing of internals piping fabrication and installation visual inspection for cleanliness, box-up inspection of static equipment, hydro testing, punch listing, preservation and maintenance of static equipment, tightness, supports, monitor mechanical discipline project quality and progress. Specifically incumbent with: Monitor, inspect, audit and guide all activities related to general mechanical, piping, non-destructive inspection, piping installation and testing, equipment installation and its internals performed by the EPC contractor in order to achieve a safe, healthy, environmentally friendly, timely and within budget realization of the project. Show less

• 

  Exxonmobil

  May 2012 - Nov 2012

  Construction superintendent

  Oversees site contractors during Construction Phase and responsible for project HSE, construction performance, quality assurance and oversight, planning and general site-wide coordination and construction activities. Assists in early site construction planning/construction planning interface with Company contractor prior to site mobilization. Serves as day-to-day interface with Company contractor/craft labor during the Construction Phase, providing a focus on safety, quality, cost, and schedule. Interfaces with QA/QC personnel to address quality issues and progress. Provides oversight of contractor’s materials management/verification systems. Ensures compliance with specifications, procedures, and plans. Monitors workforce productivities/progress relative to schedule. Liaises with contractor for field level changes, e.g., scope, costs, etc. Verifies post-site arrival of procured equipment and engineering equipment. Serves as liaison with Site Manager on barriers/emerging issues. Provides pre-commissioning/mechanical completion oversight/verification. Accountable for safe, on cost and schedule delivery and assurance for site project execution and construction activities. Supervises the mechanical completion phase and transition to final Hookup and Commissioning Phase (punch list management via Company contractor). Engage work scope contract holders to ensure the construction team work plan and their scopes are aligned and that execution proceeds in line with agreed scope. Manage and resolve construction and interface issues or conflicts as they arise. Interface with operations for seamless HSE and handover operations. Act as lead for all construction related HSE related incidents. Show less

• 

  Santos ltd

  Dec 2012 - Jan 2016

  Technical compliance engineer - mechanical/piping / welding

  As an integral member of the GLNG Plant Project Team, Responsible for Ensuring that all Piping and Static Equipment are compliance to the applicable engineering codes & standards and approved welding specifications are correctly implemented and adhered to by the principle EPC Contractor and subcontractors, review cause and effect data of welding and manufacturing defects, and review and monitor the EPC Contractor’s inspection and examination schedules and programs for compliance with Project requirements. Show less

• 

  Adnoc group (formerly zadco)

  Dec 2015 - Apr 2016

  Sr construction supervisor- mechanical &piping

  Act as COMPANY site representative on all site mechanical & piping construction works. Promote HSE awareness and ensure that all UZ750 Project HSE requirements are implemented and adhered. Responsible for construction mechanical & piping activities through the contractors supervision in respect of HSE, method, working practices, quality and timely execution of the works. Fully familiar with the assigned scope of work and interfaces with existing facilities, other projects and disciplines. Provide effective and practical construction input to ensure constructability aspects of Project Execution are adequately considered. Advise mechanical & piping UZ750 Project staff on best practices. Responsible for the mechanical & piping UZ750 Project staff aspect of Risk Management to ensure all risks/opportunities are identified and appropriate controls and mitigations developed and implemented. Responsible for mechanical & piping coordination with regard to SIMOPS and Ensure that construction hazards and risks are fully considered by designers and contractors and that appropriate mitigation actions are implemented and appropriate action taken. Initiate and manage the mechanical & piping project element of the continuous improvement processes. Ensure contractor produces appropriate execution documents in a timely manner and monitor approval and compliance. Monitors progress and performance of the construction contractor to ensure that he performs to the approved schedule, specification and standards. Interface with other IPMT groups as required ensuring a good relationship for timely and effective release of Contractors data and drawings, Technical Queries and resolution of problems. Review look-ahead schedules & ensure future work discipline interface issues are communicated and resolved. Monitor site activities for potential contractual claims problems. Maintain records of site activities and check Contractor records for accuracy. Show less

• 

  Amec foster wheeler

  May 2017 - Jan 2019

  Sr. construction supervisor - mechanical & piping
• 

  Qatarenergy lng

  Feb 2019 - Sept 2023

  Sr. mechanical piping engineer
• 

  North oil company qatar

  Oct 2023 - now

  Sr. construction field engineer