Mario Maia

Experience

• 

  FCA Fiat Chrysler Automobiles

  May 2008 - Dec 2009

  Production Trainee

  ‘Production trainee’ program focused on training manufacturing managers. After 3 months of training, I was allocated to the assembly shed, in the chassis engraving and harness assembly area. Main Responsibilities: Coordinate the activities of approximately 25 vehicle assembly operators with a focus on the pillars of World Class Manufacturing (WCM) workplace organization, autonomous maintenance, safety, and quality control. Management of absenteeism and correct sizing of employees according to the cadence of the line. Show less

• 

  CNH Industrial

  Jan 2010 - Jan 2015

  Product Engineering Analyst – February 2012 – January 2015 PASD (Power and Signal Distribution) & BoM (Bill of Material) designer responsible for Wheel Loaders, Motor Graders, Backhoe Loaders, Bulldozers, and Excavators. *Development of 2D and 3D projects using CAD tools and release of product structures for new projects. *Support in prototype validation and management of outsourced resources. Product Engineering Intern – January/2010 to January/2012 During the internship period, I worked directly in the implementation of CAD tools for the development of 2D (Vesys) and 3D (Proe Cabling) drawings in the Contagem/MG plant – until then, the only plant in the world that did not yet use the tools. *40% reduction in 2D and 3D model development time measured in the pilot project (WL48) - new New Holland Wheel Loader 12D model

  • Product analyst

    Feb 2012 - Jan 2015

  • Project intern

    Jan 2010 - Jan 2012
• 

  Energisa

  Jan 2015 - May 2016

  Project Engineer: Responsible for new automation projects and commissioning of substations and distribution equipment at Energisa Tocantins. Direct report to the area director. Management of a team of 2 engineers and 8 outsourced technicians. Capex and Opex management. During this period, we automated and delivered to the Integrated Operations Center (COI), located in Palmas/TO, 6 new substations (SE), and 13 SE scans, which will allow the relocation of 11 technicians who were on duty full-time at these sites and more than 400 pieces of equipment installed in the distribution network. Show less

  • Automation Project Enginee

    Oct 2015 - May 2016

  • Automation Project Engineer

    Jan 2015 - Oct 2015
• 

  CNH Industrial

  Jun 2016 - now

  Senior Systems Engineer, responsible for the development of electronic systems for Sprayers, Planters, and Coffee Harvesters produced in Piracicaba/SP. Direct reporting team management, reporting to the local and global manager. *Management of a team of engineers, supporting them in day-to-day activities, professional development, career planning, and succession planning; *Project management - scope, cost, deadline, deliveries, and quality, using the GPD 3.0 methodology (Global Product Development - based on PMBoK); *Preparation and presentation of monthly reports to the global governance committee of the Vehicle Electronics team; *Development of high and low-level requirements for software development, functional requirements, systems architecture diagram, network requirements, and product integration. Show less Responsible for the development of electrical diagrams and harnesses of vehicles developed in Contagem/MG, Wheel Loaders, Motor Graders, Backhoe Loaders, Crawler Tractors, and Excavators. Member of the innovation team. *Development of 2D and 3D projects using CAD tools and release of bill of materials for new projects. *Development of the “TLB Wireless” innovation project that sought to reduce the number of electrical wires in the machine through the introduction of wireless, in partnership with SENAI/SC. Show less

  • Vehicle Core Electronics Manager - Crop Production

    Jul 2023 - now

  • Electronic Systems Development Coordinator

    Sept 2017 - Jul 2023

  • Product development engineer

    Jun 2016 - Aug 2017